• <nav id="m8uo2"><option id="m8uo2"></option></nav>
  • <code id="m8uo2"><noscript id="m8uo2"></noscript></code>
    <%=NSW.OConfig.GlobalConfig.SiteName %>
    歡迎來到耀盾地板輔料官方網站!

    登錄 | 注冊 | 收藏本站 | 在線留言 | 網站地圖

    上海耀盾裝飾材料有限公司上海耀盾裝飾材料有限公司

    分享到:

    產品供應熱線:400-099-3739

    熱門關鍵詞:

    超強抗凍、環保配方
    當前位置:首頁 » 耀盾資訊中心 » 耀盾百科 » 彈性塑料地板如何選用膠水

    彈性塑料地板如何選用膠水

    文章出處:責任編輯:作者:人氣:-發表時間:2014-06-16 字體大小:【

    應用Application

    ²       PVC材質的片材(如:透心板、繡花板)PVC sheet material (e.g. embroidered sheet and through the heart sheet)

    ²       部分PVC材質的卷材(如:透心板、發泡底的卷材及柔質材料)PVC coil material

    ²       PVC底的片、卷地毯 Sheet and coil carpet with PVC end.

    優點Advantage

    ²       水基膠對使用者無害,無危險,有利于環境保護。Water-based glue is non hazardous and dangerous to environment.

    ²       適用于所有類型的工地(新房建筑或舊房翻新)Apply to all construction site (New house or renovation of old house)

    ²       可用于吸收性基材,及大部分非吸收性基材和彈性基材 It can be used for absorbent substrate, non substrate and flexible substrate.

    ²       粘結力強(適用于片材、卷材)Strong bond strength (apply to sheet and coil material)

    ²       涂布量大,在正常地面及正常操作下可達79m2/kg Large coating, normal consumption at normal ground can be used 79m2/kg.

    140-180 m2/20kBarrel    70-90 m210kg/ Barrel

    ²        干法粘貼(有利于地材的保潔、方便施工),特殊情況下也可半干粘貼 Dry paste(It is beneficial for material cleaning and construction), semi-dry paste on special condition

    ²       適用于暖氣地面能抵抗帶滑輪座椅的磨擦 Apply for resistant to friction with the pulley seat on heating surface.

    特征Character:

    ²       白色或微黃色乳狀液體 White or light yellowish milky liquid

    ²       施工開放時間:在攝氏23度時為10120分鐘(根據濕度、溫度、吸收情況、上膠量及通風性而異)construction opening time: 10 to 120 minutes at 23 oC. (According to humidity, temperature, absorption and ventilation)

    ²       初期施工建議用A1/A2的刮齒的刮刀 Recommend to use scrapting blade with A1/A2 teeth during the initial construction.

    載體準備Carrier preparation

    ²       載體必須堅固、干燥、干凈、平整、光滑、不起砂 The carrier must be strong, dry, clean, level, smooth and free sand.

    ²       不得使涂層有返潮的危險 The coating shall not have the risk of damp.

    ²       上膠時,濕度不得超過55%,須嚴格遵守載體晾干時間 Humidity can not exceed 55% when coating. Worker must strict compliance with carrier drying time.

    工作條件Working condition

    ²       溫度Temperature:工作地點溫度必須在攝氏1045之間(至少上膠前幾天必須獲得);空氣濕度:應小于55%HR;地面溫度:不小于10攝氏度Temperature in working location should be between 10 to 45 degree (Site temperature should be checked before coating); air humidity: less than 55%HR; ground temperature: less than 10 degree.

    ²       鋪設前48小時關閉地面暖氣,鋪設七天后方能重新逐漸啟動暖氣,膠粘劑和材料(切割和垂直鋪設的幅面)建議提前幾天儲存在工作地點,該處溫度至少要達到攝氏10度以上,這個作法有利于幅面的穩定,并方便于涂層操作。Shut off ground heating system before construction. 7 days later after construction, the heating can be open gradually. Adhesive and material which is in cutting and vertical laying format will be stored in the construction site several days ago before construction. The site temperature is at least above 10 oC.

    ²       施工中,潮濕會引起地板表面起泡,影響外觀。請注意防潮氣。During construction, humidity can cause bubble of floor surface. It will impact appearance of ground floor. Pay attention to avoid moisture.

    上膠 Paste Glue

    選用合適的刮刀,將粘膠在載體上單層涂上(根據材料的吸收和粗糙適度而異) according to material absorption and roughness, chose the suitable scraping blade and put the glue on carrier. Then, single-layer coat.

    ²       選用A1刮齒時,每平方涂125左右 Use A1 teeth, 125g per square meter

    ²       選用A2刮齒時,每平方涂150左右 Use A2 teeth, 150g per square meter

    ²       刮刀的齒不能過度損壞,上述粘膠用量指刮刀嶄新情況下的用量,涂膠量以現場實際為準 The teeth of blade can not been excessive damaged. The above usage of glue depends on the teeth quality. Amount of glue based on actual site condition.

    膠合方式 Method

    ²       本產品屬于含水乳膠,通過組合前水蒸發,以及材料吸收后完成干燥膠合,膠合和晾干的速度取決于粘膠厚度,材料吸收性能、溫度、濕度及通風性。The product is water-based glue. After water evaporation, material absorption and dry, glue is becoming. Speed of glue and dry depends on thickness of glue, property of material, temperature, humidity and ventilation.

    待候時間Waiting time

    根據室溫,材料的吸收和粗糙程度,以及上膠量進行調整 According to room temperature, absorption of material, roughness and amount of glue, waiting time can be adjusted.

    ²       干粘法:待候時間為10-20分鐘(室溫攝氏23度時)用量大約為140/平方米,待膠水完全透明后即可施工 Dry paste: waiting time is 10 – 20 minutes (RT: 23 oC).  The amount of glue is 140 g/m2. After glue is becoming transparent, the construction can be start.

    ²       部分特殊情況下也可半干粘貼 Half dry paste may be used in some special condition.

    開放時間 Opening time

    ²       根據溫度,材料空隙度和上膠量而異:約為10-240分鐘之間(依現場溫度而異,原則上溫度越高可工作時間越長)According to temperature and material voidage and glue amount, about 10 to 240 minutes.(According to site temperature, the higher the temperature the longer working hour)

    ²       工作時間為120分鐘之內均可Working time is within 120 minutes

    裱平Level

    ²       鋪設時,由里向外逐漸裱平 Level from the inside out

    ²       利用裱平的把子,探測涂層下面可能出現的鼓起處,并用力將其消除Use level tools to detect the muster under the coating and eliminate it firmly.

    ²       20分鐘后,再用重型滾筒(重約60公斤)仔細壓平整個表面(原則上越重越好)20 minutes later, heavy roller with 60 kg flat whole surface. More heavy more better.

    ²       裱平必須先橫向進行,隨后再縱向進行 Level must start from lateral direction and then vertical direction.

     

    最終粘結 Final adhesion

    ²       原則上鋪設24小時后,可打蠟處理In principle pasting after 24 hrs, do waxing.

    ²       鋪設4872小時后,可以用水拖洗或反復使用Pasting after 48 to 72 hrs, the floor can be washed and cleaned repeatedly.

    ²       粘貼好后應用清水沖洗粘膠新鮮斑點和鋪設工具After pasting, fresh spot and tools are flushed by clean water.

    安全須知 Safety attention

    ²       水性膠,非易燃品 Water based glue, non-combustible product.

    ²       不含溶劑,對使用者無害Free solvent and none hazardous to user.

    ²       屬可運輸類Transportability

    包裝Package

    20公斤塑料桶裝20kg per plastic barrel;10公斤塑料桶裝10kg per plastic barrel;5公斤塑料桶裝5kg per plastic barrel

    儲存Storage

    ²       在攝氏5度(零上)和30度之間,原裝產品可最多保存1The product can be stored at most for one year between 5 to 30 oC.

    ²       避免本品結冰Avoid frozen

    ²       用后關緊容器蓋子Close barrel tightly after use

    ²       一次靜止時最多疊放4 Stacked up to 4 level.

    簡述Description

    1.         基面必須要求結實、平整、光滑、干燥、干凈不起沙Base surface should be stiff, flat, smooth, dry, clean and no sand.

    2.         該產品粘結力很強,使用方便,要求干法粘貼,待膠水呈透明狀時,干透后方鋪設施工。The product has strong adhesion and easy construction. It is required drying paste. After it become transparent and totally dry, paving work can be done.

    3.         本產品適用于PVC塑料地板、片材、卷材,具體鋪設可依實際情況為準。The product is applied to PVC plastic floor, sheet and coil material. Detail laying follow the actual situation.

    4.         涂布量大,在正常情況下,涂布量為:7-9平方米/kg。Large amount of coating at normal condition. Coating amount is: 7-9 m2/kg.

    5.         建議施工時使用A2或近似A2的自制刮刀,先小面積試用,后大面積使用,刮 刀齒深最好控制在1.0-1.6毫米之間,不可無齒粘貼。Recommend to use A2 or similar A2 scraper. Firstly, try to paste within small area then large scale use. The teeth height of scraper is between 1.0-1.6 mm. The scraper without teeth is not allowed to use for pasting.

    6.         實行單面上膠,也可雙面上膠。One either side can also be double-sided adhesive glue.

     

    相關資訊

    女人的天堂免费AV在线下载_96在线啪在线观看视频免费_在线一区二区_久久久久久AV无码免费网站H
  • <nav id="m8uo2"><option id="m8uo2"></option></nav>
  • <code id="m8uo2"><noscript id="m8uo2"></noscript></code>